Ch5

Mobile Computing

Chapter 5
GSM
Asoke K Talukder
Hasan Ahmed
© Tata McGraw Hill

Global System for Mobile Communications
 Originally GSM stood for Groupe Speciale Mobile
 GSM to meet the following business objectives
1. Support for international roaming
2. Good speech quality
3. Ability to support handheld terminals
4. Low terminal and service cost
5. Spectral efficiency
6. Support for a range of new services and facilities
7. ISDN compatibility

Use of TDMA and FDMA in GSM

 Uses a combination of FDMA (Frequency Division Multiple
Access) and TDMA (Time Division Multiple Access)
 Allocation of 50 MHz (890–915 MHz and 935–960 MHz)
bandwidth in the 900 MHz frequency band and using FDMA
further divided into 124 (125 channels, 1 not used) channels
each with a carrier bandwidth of 200 KHz
 Using TDMA, each of the above mentioned channels is
then further divided into 8 time slots
 So, with the combination of FDMA and TDMA, a
maximum of992 channels for transmit and receive can be
realized

Frequency reuse in GSM

 To serve hundreds of thousands of users, the frequency must be
reused and this is done through cells.
 The area to be covered is subdivided into radio zones or
cells. Though in reality these cells could be of any shape,
for convenient modeling purposes these are modeled as
hexagons. Base stations are positioned at the center of
these cells.
 Each cell i receives a subset of frequencies fbi from the
total set assigned to the respective mobile network. To
avoid any type of co-channel interference, two neighboring
cells never use the same frequencies.

Frequency reuse in GSM
 Only at a distance of D (known as frequency reuse
distance), the same frequency from the set fbi can be
reused. Cells with distance D from cell i, can be assigned
one or all the frequencies from the set fbi belonging to cell i.
 When moving from one cell to another during an ongoing
conversation, an automatic channel change occurs. This
phenomenon is called handover. Handover maintains an
active speech and data connection over cell boundaries.
 The regular repetition of frequencies in cells result in a
clustering of cells. The clusters generated in this way can
consume the whole frequency band. The size of a cluster is
defined by k, the number of cells in the cluster. This also
defines the frequency reuse distance D. The figure in next
slide shows an example of cluster size of 4.

GSM System Hierarchy

 Consists at the minimum one administrative region
assigned to one MSC (Mobile Switching Centre)
 Administrative region is commonly known as PLMN
(Public Land Mobile Network)
 Each administrative region is subdivided into one or
many Location Area (LA)
 One LA consists of many cell groups and each cell group
is assigned to one BSC (Base Station Controller)
 For each LA, there will be at least one BSC while cells in
one BSC can belong to different LAs

GSM Architecture

 Cells are formed by the radio areas covered by a BTS
(Base Transceiver Station)
 Several BTSs are controlled by one BSC
 Traffic from the MS (Mobile Station) is routed through
MSC
 Calls originating from or terminating in a fixed network or
other mobile networks is handled by the GMSC (Gateway
MSC)

Operational Architecture of GSM

Home Location Register (HLR) in GSM

 It contains the following information:
1. Authentication information like International Mobile
Subscriber Identity (IMSI)
2. Identification information like name, address, etc. of the
subscriber
3. Identification information like Mobile Subscriber ISDN
(MSISDN) etc.
4. Billing information like prepaid or postpaid
5. Operator selected denial of service to a subscriber


6. Handling of supplementary services like for CFU (Call
Forwarding Unconditional), CFB (Call Forwarding Busy),
CFNR (Call Forwarding Not Reachable) or CFNA (Call
Forwarding Not Answered)
7. Storage of SMS Service Center (SC) number in case the
mobile is not connectable so that whenever the mobile is
connectable, a paging signal is sent to the SC
8. Provisioning information like whether long distance and
international calls allowed or not
9. Provisioning information like whether roaming is enabled
or not


10. Information related to auxiliary services like Voice mail, data,
fax services, etc.
11. Information related to auxiliary services like CLI (Caller Line
Identification), etc.
12. Information related to supplementary services for call routing.
In GSM network, one can customize the personal profile to
the extent that while the subscriber is roaming in a foreign
PLMN, incoming calls can be barred. Also, outgoing
international calls can be barred, etc.
13. Some variable information like pointer to the VLR, location
area of the subscriber, Power OFF status of the handset,
etc.

Entities in GSM

 The Mobile Station (MS) - This includes the Mobile
Equipment (ME) and the Subscriber Identity Module (SIM).
 The Base Station Subsystem (BSS) - This includes the Base
Transceiver Station (BTS) and the Base Station Controller (BSC).
 The Network and Switching Subsystem (NSS) - This includes
Mobile Switching Center (MSC), Home Location Register (HLR),
Visitor Location Register (VLR), Equipment Identity Register
(EIR), and the Authentication Center (AUC).
 The Operation and Support Subsystem (OSS) - This includes
the Operation and Maintenance Center (OMC).

Mobile Station
 Mobile Station (MS) consists of two main elements: mobile
equipment or mobile device (that is the phone without the
SIM card) and Subscriber Identity Module (SIM)
 Terminals distinguished principally by their power and
application
 SIM is installed in every GSM phone and identifies the
terminal
 SIM cards used in GSM phones are smart processor
cards with a processor and a small memory
 SIM card contains the International Mobile Subscriber
Identity (IMSI) used to identify the subscriber to the system,
a secret key for authentication, and other security
information

Base Station Subsystem

 Base Station Subsystem (BSS) connects the Mobile
Station and the Network and Switching Subsystem (NSS)
 In charge of the transmission and reception for the last
mile
 BSS can be divided into two parts: Base Transceiver
Station (BTS) or Base Station and Base Station Controller
(BSC)
 Base Transceiver Station corresponds to the transceivers
and antennas used in each cell of the network
 BTS is usually placed in the center of a cell and its
transmitting power defines the size of a cell

Base Station Subsystem

 BTS houses the radio transmitter and the receivers that define a
cell and handles the radio-link protocols with the Mobile Station
while handling between one and sixteen transceivers depending
on the density of users in the cell
 Base Station Controller is the connection between the BTS and
the Mobile service Switching Center (MSC) and manages the
radio resources for one or more BTSs
 BSC handles handovers, radio-channel setup, control of radio
frequency power levels of the BTSs, exchange function, and the
frequency hopping

Network and Switching Subsystem

 Central component of the Network Subsystem is the
Mobile Switching Center (MSC)
 Signaling between functional entities in the Network
Subsystem uses Signaling System Number 7 (SS7)
 MSC together with Home Location Register (HLR) and
Visitor Location Register (VLR) databases, provide the
call-routing and roaming capabilities of GSM
 MSC does the following functions:
1. It acts like a normal switching node for mobile
subscribers of the same network (connection between
mobile phone to mobile phone within the same network)


2. It acts like a normal switching node for the PSTN fixed
telephone (connection between mobile phone to fixed
phone)
3. It acts like a normal switching node for ISDN
4. It provides all the functionality needed to handle a
mobile subscriber, such as registration, authentication,
location updating, handovers and call routing
5. It includes databases needed in order to store
information to manage the mobility of a roaming
subscriber

Network Switching Subsystem

 MSC together with Home Location Register (HLR) and
Visitor Location Register (VLR) databases, provide the call-
routing and roaming capabilities of GSM
 HLR contains all the administrative information of each
subscriber registered in the corresponding GSM network
 Location of the mobile is typically in the form of the
signaling address of the VLR associated with the mobile
station
 HLR is always fixed and stored in the home network,
whereas the VLR logically moves with the subscriber
 VLR is similar to a cache, whereas HLR is the persistent
storage


 VLR contains selected administrative information
borrowed from the HLR, necessary for call control and
provisioning of the subscribed services
 When a subscriber enters the covering area of a new
MSC, the VLR associated with this MSC can request
information about the new subscriber from its corresponding
HLR in the home network
 There is a component called Gateway MSC (GMSC) that
is associated with the MSC


 GMSC is the interface between the mobile cellular
network and the PSTN and also is in charge of routing calls
from the fixed network towards a GSM user and vice versa
 GMSC is often implemented in the same node as the
MSC
 GIWU (GSM Inter Working Unit) corresponds to an
interface to various networks for data communications

Operation and Support Subsystem

 Operations and Support Subsystem (OSS) controls and
monitors the GSM system
 OSS is connected to the different components of the
NSS and to the BSC and also in charge of controlling the
traffic load of the BSS
 Equipment Identity Register (EIR) rests with OSS
 EIR is a database that contains a list of all valid mobile
equipment within the network, where each mobile station is
identified by its International Mobile Equipment Identity
(IMEI)
 EIR contains a list of IMEIs of all valid terminals

Operation and Support Subsystem

 An IMEI is marked as invalid if it has been reported stolen or is
not type approved
 The EIR allows the MSC to forbid calls from this stolen or
unauthorized terminals
 Authentication Center (AUC) is responsible for the
authentication of a subscriber
 AUC is a protected database and stores a copy of the secret key
stored in each subscriber’s SIM card

Short Message Service

 Short Message Service (SMS) is one of the most popular
services within GSM
 SMS is a data service and allows a user to enter text
message up to 160 characters in length when 7 bit English
characters are used
 SMS is a proactive bearer and is an ‘always on’ network
 Message center is referred to as Service Centre (SC) or
SMS Controller (SMSC)
 SMSC is a system within the core GSM network which
works as the store and forward system for SMS messages

SMS

 Two types of SMS: SMMT (Short Message Mobile Terminated
Point-to-Point) and SMMO (Short Message Mobile Originated
Point-to-Point)
 SMMT is an incoming short message from the network and is
terminated in the MS (phone or Mobile Station)
 SMMO is an outgoing message originated in the MS, and
forwarded to the network for delivery
 For an outgoing message, the SMS is sent from the phone to
SC via the VLR and the Inter Working MSC (IWMSC)
 For incoming message, the path is from SC to the MS via the
HLR and the Gateway MSC (GMSC)

From speech to radio waves

 Digitizer and source coding: The user speech is digitized at 8
KHz sampling rate using Regular Pulse Excited–Linear Predictive
Coder (RPE–LPC) with a Long Term Predictor loop where
information from previous samples is used to predict the current
sample. Each sample is then represented in signed 13-bit
linear PCM value. This digitized data is passed to the coder
with frames of 160 samples where encoder compresses
these 160 samples into 260-bits GSM frames resulting in
one second of speech compressed into 1625 bytes and
achieving a rate of 13 Kbits/sec.


 Channel coding: This introduces redundancy into the data for
error detection and possible error correction where the gross bit
rate after channel coding is 22.8 kbps (or 456 bits every 20 ms).
These 456 bits are divided into eight 57-bit blocks and the result is
interleaved amongst eight successive time slot bursts for
protection against burst transmission errors.
 Interleaving: This step rearranges a group of bits in a particular
way to improve the performance of the error-correction
mechanisms. The interleaving decreases the possibility of losing
whole bursts during the transmission by dispersing the errors.
 Ciphering: This encrypts blocks of user data using a symmetric
key shared by the mobile station and the BTS.

 Burst formatting: It adds some binary information to the
ciphered block for use in synchronization and equalization
of the received data.
 Modulation: The modulation technique chosen for the
GSM system is the Gaussian Minimum Shift Keying
(GMSK) where binary data is converted back into analog
signal to fit the frequency and time requirements for the
multiple access rules. This signal is then radiated as radio
wave over the air.
 Multipath and equalization: An equaliser is in charge of
extracting the ‘right’ signal from the received signal while
estimating the channel impulse response of the GSM system and
then it constructs an inverse filter. The received signal is then
passed through the inverse filter.


 Synchronization: For successful operation of a mobile radio
system, time and frequency synchronization are needed.
Frequency synchronization is necessary so that the transmitter and
receiver frequency match (in FDMA) while Time synchronization
is necessary to identify the frame boundary and the bits within the
frame (in TDMA).
 To avoid collisions of burst transmitted by MS with the
adjacent timeslot such collisions, the Timing Advance
technique is used where frame is advanced in time so that
this offsets the delay due to greater distance. Using this
technique and the triangulation of the intersection cell sites,
the location of a mobile station can be determined from
within the network.

Call Routing

 The directory number dialed to reach a mobile subscriber is
called the Mobile Subscriber ISDN (MSISDN) which is defined
by the E.164 numbering plan and includes a country code and a
National Destination Code, which identifies the subscriber’s
operator. The first few digits of the remaining subscriber number
may identify the subscriber’s HLR within the home PLMN
 For example, the MSISDN number of a subscriber in
Bangalore associated with Airtel network is +919845XYYYYY
which is a unique number and understood from anywhere in the
world. Here, + means prefix for international dialing, 91 is the
country code for India and 45 is the network operator’s code
(Airtel in this case). X is the level number managed by the
network operator ranging from 0 to 9 while YYYYY is the
subscriber code which , too, is managed by the operator.

Call Routing

 The call first goes to the local PSTN exchange where
PSTN exchange looks at the routing table and determines
that it is a call to a mobile network.
 PSTN forwards the call to the Gateway MSC (GMSC) of
the mobile network.
 MSC enquires the HLR to determine the status of the
subscriber. It will decide whether the call is to be routed or
not. If MSC finds that the call can be processed, it will find
out the address of the VLR where the mobile is expected to
be present.

Call Routing

 If VLR is that of a different PLMN, it will forward the call to
the foreign PLMN through the Gateway MSC. If the VLR is
in the home network, it will determine the Location Area
(LA).
 Within the LA, it will page and locate the phone and
connect the call.

PLMN Interfaces

 Basic configuration of a GSM network contains a central
HLR and a central VLR where HLR contains all security,
provisioning and subscriber related information and VLR
stores the location information and other transient data.
 MSC needs subscriber parameter for successful call set-
up.
 Any data related to user call (connection, teardown etc.)
are processed with SS7 protocol for signaling using ISUP
(ISDN User Part) stack between network nodes.
 For mobile specific signaling, a protocol stack called MAP
(Mobile Application Part) is used over the SS7 network
which does all database transactions and
handover/roaming transactions between the MSC.

GSM Addresses and Identifiers
 International Mobile Station Equipment Identity (IMEI): Every
mobile equipment in this world has a unique identifier which is
called IMEI. IMEI is allocated by the equipment manufacturer
and registered by the network operator in the Equipment Identity
Register (EIR).
 International Mobile Subscriber Identity (IMSI): When
registered with a GSM operator, each subscriber is assigned a
unique identifier called IMSI which is stored in the SIM card and
secured by the operator. IMSI consists of several parts: 3 decimal
digits of Mobile Country Code (MCC), 2 decimal digits of Mobile
Network Code (MNC) and a maximum of 10 decimal digits of
Mobile Subscriber Identification Number (MSIN) which is a
unique number of the subscriber within the home network.


 Mobile Subscriber ISDN Number (MSISDN): The MSISDN
number is the real telephone number as is known to the external
world. MSISDN number is public information whereas IMSI is
private to the operator. IMSI can be multiple such as when a
subscriber opts for fax and data, he is assigned a total of three
numbers: one for voice call, one for fax call and another for data
call. MSISDN follows the international ISDN (Integrated Systems
Data Network) numbering plan.
 ISDN has Country Code (CC) of 1 to 3 decimal digits, National
Destination Code (NDC) of 2 to 3 decimal digits and Subscriber
Number (SN) of maximum 10 decimal digits.


 Location Area Identity: Each LA in a PLMN has its own
identifier called Location Area Identifier (LAI) which is structured
hierarchically and unique. LAI consists of 3 digits of CC, 2 digits
of Mobile Network Code and maximum of 5 digits of Location
Area Code.
 Mobile Station Roaming Number (MSRN): When a subscriber
is roaming in another network, a temporary ISDN number is
assigned to the subscriber called MSRN. MSRN is assigned by
the local VLR in charge of the mobile station and follows the
structure of MSISDN.

 Temporary Mobile Subscriber Identity (TMSI): TMSI is a
temporary identifier assigned by the serving VLR used in place of
the IMSI for identification and addressing of the mobile station.
Together with the current location area, a TMSI allows a
subscriber to be identified uniquely.
 Local Mobile Subscriber Identity (LMSI): LMSI is assigned by
the VLR and stored in the HLR and is used as a searching key for
faster database access within the VLR.
 Cell Identifier: Within a LA, every cell has a unique Cell
Identifier (CI) and together with a LAI, a cell can be identified
uniquely through Global Cell Identity (LAI & CI).
 MSCs and Location Registers (HLR & VLR) are addressed
with ISDN numbers while they may use a Signaling Point Code
(SPC) within a PLMN.

Network aspects in GSM

Signaling protocol structure in GSM


 Layer 1 is the physical layer which uses the channel structures
over the air interface.
 Layer 2 is the data link layer and across the Um interface, the
data link layer is a modified version of the LAPD protocol used in
ISDN or X.25, called LAPDm.
 Across the A interface, the Message Transfer Part layer 2 of
Signaling System Number 7 is used.


 Layer 3 of the GSM signaling protocol is itself divided
into three sub-layers:
1. Radio Resources Management: It controls the set-up,
maintenance and termination of radio and fixed channels,
including handovers.
2. Mobility Management: It manages the location updating and
registration procedures as well as security and authentication.
3. Connection Management: It handles general call control and
manages Supplementary Services and the Short Message
Service.

Handover

 The procedure of change of resources is called handover when
the user is mobile while the call is in progress.
 There are four different types of handover in the GSM system,
which involve transferring a call between:
1. Channels (time slots) in the same cell
2. Cells (Base Transceiver Stations) under the control of the
same Base Station Controller (BSC)
3. Cells under the control of different BSCs but belonging to the
same Mobile Switching Center (MSC)
4. Cells under the control of different MSCs

Handover

 First two types of handover, called internal handovers, involve
only one Base Station Controller (BSC). To save signaling
bandwidth, they are managed by the BSC without involving the
Mobile services Switching Center (MSC), except to notify it at the
completion of the handover.
 Last two types of handover, called external handovers, are
handled by the MSC.

Mobility Management

 Mobility Management (MM) function handles the procedures
that arise from the mobility of the subscriber and is in charge of
all the aspects related to the mobility of the user, especially the
roaming, the location management, and the security/authentication
of the subscriber.
 First location update procedure is called the IMSI attach
procedure where the MS indicates its IMSI to the network
whereas when a mobile station is powered off, it performs an
IMSI detach procedure in order to tell the network that it is no
longer connected.

Mobility Management

 A location update message is sent to the new MSC/VLR which
records the location area information and then sends the location
information to the subscriber’s HLR.
 If the mobile station is authenticated and authorized in the new
MSC/VLR, the subscriber’s HLR cancels the registration of the
mobile station with the old MSC/VLR.
 Location update is also performed periodically and if after the
updating time period, the mobile station has not registered, it is
then deregistered.

Mobility Management

 When there is an incoming call for a subscriber, the mobile
phone needs to be located and a channel needs to be allocated and
the call connected.
 A powered-on mobile is informed of an incoming call by a
paging message sent over the paging channel of the cells within
the current location area while location updating procedures and
subsequent call routing use MSC, HLR and VLR.
 If the subscriber is entitled to service, HLR sends a subset of
the subscriber information needed for call control to the new
MSC/VLR and sends a message to the old MSC/VLR to cancel
the old registration.

Mobility Management

 An incoming mobile terminating call is directed to the Gateway
MSC (GMSC) function which, as a switch, interrogates the
subscriber’s HLR to obtain routing information and thus contains
a table linking MSISDNs to their corresponding HLRs.
 The routing information that is returned to the GMSC is the
Mobile Station Roaming Number (MSRN).
 MSRNs are related to the geographical numbering plan and not
visible to subscribers.

Mobility Management

 Generally, GMSC queries the called subscriber’s HLR for an
MSRN.
 HLR stores only the SS7 address of the subscriber’s current
VLR while VLR temporarily allocates an MSRN from its pool for
the call.
 MSRN is returned to the HLR and back to the GMSC, which
can then route the call to the new MSC. At new MSC, IMSI
corresponding to the MSRN is looked up and the mobile station is
paged in its current location area.
 HLR is referred for incoming call whereas VLR is referred for
outgoing call.

GSM Frequency Allocation

 Normally, GSM uses 900 MHz band wherein 890-915 MHz is
allocated for the uplink (mobile station to base station) and 935–
960 MHz is allocated for the downlink (base station to mobile
station). Each way the bandwidth for the GSM system is 25 MHz
which provides 125 carriers uplink/downlink each having a
bandwidth of 200 kHz.
 ARFCN (Absolute Radio Frequency Channel Numbers) denote
a forward and reverse channel pair which is separated in
frequency by 45 MHz.
 Practically, a guard band of 100 kHz is provided at the upper
and lower end of the GSM 900 MHz spectrum and only 124
(duplex) channels are implemented.

 GSM uses a combination of Time Division Multiple Access
(TDMA) and Frequency Division Multiple Access (FDMA)
encoding.
 One or more carrier frequencies are assigned to each base
station and each of these carrier frequencies is then divided in
time using a TDMA scheme where fundamental unit is called a
burst period lasting approximately 0.577 ms.
 Eight burst periods are grouped into a TDMA frame of
approximately 4.615 ms which forms the basic unit for the
definition of logical channels.
 One physical channel is one burst period per TDMA frame
while, normally, channels are defined by the number and position
of their corresponding burst periods.


Carrier frequencies and TDMA frames

Authentication and Security

 Authentication involves two functional entities - the SIM card
in the mobile phone and the Authentication Center (AUC).
 Following authentication by algorithm A3, a key is generated
for encryption.
 An algorithm A8 is used to generate the key while a different
algorithm called A5 is used for both ciphering and deciphering
procedures for signaling, voice and data.
 So, SS7 signal, voice, data, and SMS within GSM networks are
ciphered over the wireless radio interface.

A3 Algorithm

 During authentication, MSC challenges the MS with a random
number (RAND).
 SIM card uses this RAND received from the MSC and a secret
key Kj stored within the SIM as input. Both the RAND and the Kj
secret are 128 bits long. Using the A3 algorithm with RAND and
Kj as input a 32-bit output called signature response (SRES) is
generated in the MS and then sent back to MSC.
 Using the same set of algorithms, the AUC also generates a
SRES. The SRES from MS and the SRES generated by the AUC
are compared.
 If they are the same, the MS is authenticated.

A3 Algorithm

 The idea is that no keys will be transacted over the air.
However, if the SRES values calculated independently by the SIM
and the AUC are the same, then Kj has to be same and if Kj is
same, SIM card is genuine.

A8 Algorithm

 A8 algorithm is the key generation algorithm.
 A8 generates a session key, Kc, from the random challenge
RAND (received from the MSC) and from the secret key Kj.
 Keys are generated at both the MS and the network end. The
session key, Kc, is used for ciphering till the MSC decides to
authenticate the MS once again.

A5 Algorithm
 A5 is the stream cipher algorithm used to encrypt over-the-air
transmissions. The stream cipher is initialized all over again for
every frame sent with the session key, Kc, and the number of the
frame being encrypted or decrypted.
 Same Kc is used throughout the call but the 22-bit frame
number changes during the call, thus, generating a unique key
stream for every frame.

Next Chapter

Short Message Service

Thanks

Ch5

More Related Content

What's hot

Viewers also liked

Similar to Ch5

Recently uploaded

Ch5