CCNA 2 Routing and Switching v5.0 Chapter 8

Chapter 8: Single-Area
OSPF
Routing & Switching
© 2008 Cisco Systems, Inc. All Presentation_ID rights reserved. Cisco Confidential 1

Chapter 8
8.1 Characteristics of OSPF
8.2 Configuring Single-area OSPFv2
8.3 Configure Single-area OSPFv3
Presentation_ID © 2008 Cisco Systems, Inc. All rights reserved. Cisco Confidential 2

Chapter 8: Objectives

Open Shortest Path First
Evolution of OSPF
Interior Gateway Protocols
1988
1989
updated in
2008

Features of OSPF

Components of OSPF

Components of OSPF (cont.)
OSPF Routers Exchange Packets - These packets are
used to discover neighboring routers and also to
exchange routing information to maintain accurate
information about the network.

Link-State Operation
If a neighbor is present,
the OSPF-enabled
router attempts to
establish a neighbor
adjacency with that
neighbor

Link-State Operation (cont.)
 LSAs contain the state
and cost of each directly
connected link.
 Routers flood their LSAs
to adjacent neighbors.
 Adjacent neighbors
receiving the LSA
immediately flood the LSA
to other directly connected
neighbors, until all routers
in the area have all LSAs.

Link-State Operation
 Build the topology table
based on the received
LSAs.
 This database eventually
holds all the information
about the topology of the
network.
 Execute the SPF
Algorithm.

Link-State Operation (cont.)
From the SPF tree,
the best paths are
inserted into the
routing table.

Single-area and Multiarea OSPF

Single-area and Multiarea OSPF (cont.)

OSPF Messages
Encapsulating OSPF Messages

OSPF Messages
Types of OSPF Packets

OSPF Messages
Hello Packet
OSPF Type 1 packet = Hello packet:
 Discover OSPF neighbors and establish
neighbor adjacencies.
 Advertise parameters on which two routers
must agree to become neighbors.
 Elect the Designated Router (DR) and
Backup Designated Router (BDR) on
multiaccess networks like Ethernet and
Frame Relay.

OSPF Messages
Hello Packet (cont.)

OSPF Messages
Hello Packet Intervals
OSPF Hello packets are transmitted:
 To 224.0.0.5 in IPv4 and FF02::5 in IPv6 (all OSPF
routers)
 Every 10 seconds (default on multiaccess and point-to-point
networks)
 Every 30 seconds (default on non-broadcast
multiaccess [NBMA] networks)
 Dead interval is the period that the router waits to
receive a Hello packet before declaring the neighbor
down
 Router floods the LSDB with information about down
neighbors out all OSPF enabled interfaces
 Cisco’s default is 4 times the Hello interval

OSPF Messages
Link-State Updates

OSPF Operation
OSPF Operational States
When an OSPF router is
initially connected to a
network, it attempts to:
 Create adjacencies
with neighbors
 Exchange routing
information
 Calculate the best
routes
 Reach convergence
 OSPF progresses
through several states
while attempting to
reach convergence.

OSPF Operation
Establish Neighbor Adjacencies

OSPF Operation
Establish Neighbor Adjacencies (cont.)
DR and BDR election only occurs on multi-access networks such as Ethernet LANs.

OSPF Operation
OSPF DR and BDR

OSPF Operation
Synchronizing OSPF Database

OSPF Operation
Synchronizing OSPF Database (cont.)

OSPF Router ID
OSPF Network Topology

OSPF Router ID
Router IDs

Configure Single-area OSPFv2
The network Command

Configure Single-Area OSPFv2
Passive Interface
 By default, OSPF messages are forwarded out all OSPF-enabled
interfaces. However, these messages really only need to be sent
out interfaces connecting to other OSPF-enabled routers.
 Sending out unneeded messages on a LAN affects the network in
three ways:
 Inefficient Use of Bandwidth
 Inefficient Use of Resources
 Increased Security Risk
 The Passive Interface feature helps limiting the scope of routing
updates advertisements.

Configure Single-area OSPFv2
Configuring Passive Interfaces
Use the passive-interface router
configuration mode command to prevent the
transmission of routing messages through a
router interface, but still allow that network to
be advertised to other routers.

OSPF Cost
OSPF Metric = Cost
Cost = reference bandwidth / interface bandwidth
(default reference bandwidth is 10^8)
Cost = 100,000,000 bps / interface bandwidth in bps

OSPF Cost
OSPF Accumulates Costs
Cost of an OSPF route is the accumulated value from one router to the
destination network.

OSPF Cost
Adjusting the Reference Bandwidth
 Use the command - auto-cost reference-bandwidth
 Must be configured on every router in the OSPF domain
 Notice that the value is expressed in Mb/s:
 Gigabit Ethernet - auto-cost reference-bandwidth 1000
 10 Gigabit Ethernet - auto-cost reference-bandwidth 10000

OSPF Cost
Default Interface Bandwidths
On Cisco routers, the default bandwidth on most serial interfaces is set to
1.544 Mb/s.

OSPF Cost
Adjusting the Interface Bandwidths

OSPF Cost
Manually Setting the OSPF Cost
Both the bandwidth interface command and the ip ospf cost interface
command achieve the same result, which is to provide an accurate
value for use by OSPF in determining the best route.

Verify OSPF
Verify OSPF Neighbors
Verify that the router has formed an adjacency with
its neighboring routers.

Verify OSPF
Verify OSPF Protocol Settings

Verify OSPF
Verify OSPF Process Information

Verify OSPF
Verify OSPF Interface Settings

OSPFv2 vs. OSPFv3
OSPFv3

OSPFv2 vs. OSPFv3
Similarities Between OSPFv2 to OSPFv3

OSPFv2 vs. OSPFv3
Differences Between OSPFv2 to OSPFv3

OSPFv2 vs. OSPFv3
Link-Local Addresses
FF02::5 address is the all OSPF router address
FF02::6 is the DR/BDR multicast address

Configuring OSFPv3
OSPFv3 Network Topology

Configuring OSFPv3
OSPFv3 Network Topology (cont.)

Configuring OSFPv3
Link-Local
Addresses
 Link-local addresses are automatically created when an IPv6 global unicast
address is assigned to the interface (required).
 Global unicast addresses are not required.
 Cisco routers create the link-local address using FE80::/10 prefix and the
EUI-64 process unless the router is configured manually,
 EUI-64 involves using the 48-bit Ethernet MAC address, inserting FFFE in
the middle and flipping the seventh bit. For serial interfaces, Cisco uses the
MAC address of an Ethernet interface.
 Notice in the figure that all three interfaces are using the same link-local
address.

Configuring OSFPv3
Assigning Link-Local Addresses
Manually
configuring the link-local
address
provides the ability
to create an
address that is
recognizable and
easier to remember.

Configuring OSFPv3
Configuring the OSPFv3 Router ID

Configuring OSFPv3
Configuring the OSPFv3 Router ID (cont.)

Configuring OSFPv3
Modifying an OSPFv3 Router ID

OSPF Configuring OSFPv3
Enabling OSPFv3 on Interfaces
Instead of using the network router configuration mode
command to specify matching interface addresses,
OSPFv3 is configured directly on the interface.

Verify OSPFv3
Verify OSPFv3 Neighbors/Protocol Settings

Verify OSPFv3
Verify OSPFv3 Interfaces

Verify OSPFv3
Verify IPv6 Routing Table

Chapter 8: Summary
OSPF:
 For IPv4 is OSPFv2
 For IPv6 is OSPFv3
 Classless, link-state routing protocol with a default administrative
distance of 110, and is denoted in the routing table with a route
source code of O
 OSPFv2 is enabled with the router ospf process-id global
configuration mode command. The process-id value is locally
significant, which means that it does not need to match other OSPF
routers to establish adjacencies with those neighbors.
 Network command uses the wildcard-mask value which is the
inverse of the subnet mask, and the area-id value

Chapter 8: Summary (cont.)
OSPF:
 By default, OSPF Hello packets are sent every 10 seconds on
multiaccess and point-to-point segments and every 30 seconds on
NBMA segments (Frame Relay, X.25, ATM), and are used by OSPF
to establish neighbor adjacencies. The Dead interval is four times the
Hello interval, by default.
 For routers to become adjacent, their Hello interval, Dead interval,
network types, and subnet masks must match. Use the show ip ospf
neighborscommand to verify OSPF adjacencies.
 In a multiaccess network, OSPF elects a DR to act as collection and
distribution point for LSAs sent and received. A BDR is elected to
assume the role of the DR should the DR fail. All other routers are
known as DROTHERs. All routers send their LSAs to the DR, which
then floods the LSA to all other routers in the multiaccess network.

OSPF:
 In multiaccess networks, the router with the highest router ID is the
DR, and the router with the second highest router ID is the BDR. This
can be superseded by the ip ospf priority command on that
interface. The router with the highest priority value is the DR, and
next-highest the BDR.
 The show ip protocols command is used to verify important OSPF
configuration information, including the OSPF process ID, the router
ID, and the networks the router is advertising.
 OSPFv3 is enabled on an interface and not under router
configuration mode. OSPFv3 needs link-local addresses to be
configured. IPv6 Unicast routing must be enabled for OSPFv3. A 32-
bit router-ID is required before an interface can be enabled for
OSPFv3.

OSPF:
 The show ip protocols command is used to verify important
OSPFv2 configuration information, including the OSPF process ID,
the router ID, and the networks the router is advertising.
 OSPFv3
• Enabled on an interface and not under router configuration
mode
• Needs link-local addresses to be configured. IPv6
• Unicast routing must be enabled for OSPFv3
• 32-bit router-ID is required before an interface can be enabled
for OSPFv3
• show ipv6 protocols command is a quick way to verify
configuration information (OSPF process ID, the router ID, and
the interfaces enabled for OSPFv3)

CCNA 2 Routing and Switching v5.0 Chapter 8

More Related Content

What's hot

Similar to CCNA 2 Routing and Switching v5.0 Chapter 8

Recently uploaded

In this document

CCNA 2 Routing and Switching v5.0 Chapter 8