Encyclopedia Astronautica Home - Search - Browse - Alphabetic Index: 0- 1- 2- 3- 4- 5- 6- 7- 8- 9 A- B- C- D- E- F- G- H- I- J- K- L- M- N- O- P- Q- R- S- T- U- V- W- X- Y- Z R-56
AKA: 8K68. Status: Study 1962. Payload: 40,000 kg (88,000 lb). Thrust: 23,220.00 kN (5,220,060 lbf). Gross mass: 1,421,000 kg (3,132,000 lb). Height: 67.80 m (222.40 ft). Diameter: 6.50 m (21.30 ft). Apogee: 200 km (120 mi). After drawing back from the 'cluster of R-16's' approach of the SK-100, Yangel conducted some trade studies to determine the optimum design for his bureau's first �super rocket'. The booster was to be capable of serving as a first-strike military global rocket or as a heavy launch vehicle, placing 40 metric ton payloads into a 200 km polar orbit. The selected monoblock design could be transported on the Soviet internal canal system from the factory to the launch site. The R-56 would have been 67.8 m long and consisted of three stages, the first two with a basic diameter of 6.5 m. The first stage had a flared 8.2 m diameter base to accommodate the 16 RD-253 engines. Yangel conducted some trade studies to determine the optimum design for his bureau's first �super rocket'. The booster was to be capable of launching a range of missions:
To achieve these design objectives, three design approaches were studied in detail:
The selected monoblock vehicle was 67.8 m long and consisted of three stages, the first two with a basic diameter of 6.5 m. The first stage had a flared 8.2 m diameter base to accommodate the 16 engines. These were developed by Glushko's OKB-456, and each produced 148 metric tons of thrust at lift-off. The thrust and technical characteristics indicate they would have been identical to or closely derived from the RD-253 engine developed for Chelomei's UR-500 rocket. Twelve of the main engines were fixed while four were gimbaled in pitch to provide launch vehicle steering. Separate propellant tanks were arranged with the oxidizer forward tank forward, the fuel tank aft. It is said that the launch vehicle was equipped with a recovery system; this probably applied only to the first stage, which the figures indicate has an unusually high empty mass, perhaps including a means of recovering the stage or engine section for reuse. The second stage had a common bulkhead between the oxidizer and propellant tanks. It was equipped with a single fixed main engine of 172 metric tons thrust. The technical characteristics indicate that it was identical with the RD-254 high-expansion ration derivative of the RD-253 also developed for Chelomei's UR-700. Four vernier engines, with a total thrust of 50,000 kgf, provided ullage force for main engine ignition, steering during main engine burn, and precise velocity correction after main engine cut-off. There were two versions of the third stage: a single start variant for placement of large payloads into low earth orbit, and a multiple start version for taking smaller payloads to high earth orbit or earth escape trajectories. It was equipped with a main engine of 50,000 kgf and four vernier engines totaling 5,500 kgf. The characteristics indicate it was probably based on Kosberg's RD-0213 engine developed for the third stage of the UR-500K Proton launch vehicle. The stage, while having nearly the same diameter as the Proton third stage, differed in design, with a common bulkhead between the oxidizer and propellant tanks. A fourth stage was designed to allow insertion of payloads into geosynchronous or lunar orbit. The propellants used and engine characteristics are identical to those of the experimental RD-280 engine developed by Glushko in the mid-1960's. The stage uniquely used the Aerozine-50 fuel developed in the United States for the Titan 2 ICBM. The engine was capable of four restarts. The assembled vehicle would be moved by road from the Yangel factory in Dnepropetrovsk to the mouth of the Surya River. From there it could be moved on the Soviet Union's elaborate inland waterway system to any of the existing launch sites - Kapustin Yar on the Volga, Baikonur on the Syr Darya, or Plesetsk on the Yemtsa. Kapustin Yar, the closest to the factory, was the preferred location. At the launch site the vehicle would be moved to an austere launch pad a short distance form the river. After being put upright it would be enclosed by a service tower providing an environmentally protected environment for final rocket and payload preparation. Growth versions of the R-56 would return to the cluster principle in order to boost larger payloads, such as those required for manned lunar expeditions. The 685,000 kgf RD-270 engine was also to have been used in later versions of the R-56. This would have reduced the number of engines in the first stage from 16 to 4. Yangel's KB Yuzhnoye was the prime contractor for the launch vehicle, with support from the Soviet Academy of Sciences, NII-88, NITI-40, GSPI, and the Ministry of Defense. By 1965 Yangel had decided that the bitter fight between Chelomei and Korolev over control of manned programs was damaging the Soviet space effort. In any case he could see that the size of the projects had reached such a scale that it was impossible for one design bureau to handle all of the required elements. He proposed a collaborative effort: Yangel would design and build the launch vehicle; Korolev the manned spacecraft; and Chelomei the unmanned spacecraft. However this was not to be. The leadership was loath to change course with funds already invested in development of boosters and spacecraft by Chelomei and Korolev. The other Chief Designers objected that use of the R-56 for a manned lunar landing would require two R-56 launches in the place of one UR-700 or N1 launch. This would mean use of untried earth orbit rendezvous techniques to assemble the spacecraft in earth orbit. Development of the R-56 was not authorized, and for once in his career Yangel gave up the fight. As a practical matter it was not possible for one bureau to handle the moon landing project. Although Glushko and Chelomei refused to co-operate with Korolev on the effort, most other rocket design bureaus were involved. Yangel found himself charged with development of the LK lunar lander that would actually land a cosmonaut on the moon. Many thanks to Asif Siddiqi and Marcus Lindroos for providing source materials for this article.
LEO Payload: 40,000 kg (88,000 lb) to a 200 km orbit at 90.00 degrees. Payload: 6,000 kg (13,200 lb) to a GEO. Stage Data - R-56
Family: heavy-lift, orbital launch vehicle. Country: Ukraine. Engines: R-56 Blok A, R-56 Blok B. Stages: R-56 Block K, R-56 Block O, R-56 Block B, R-56 Block A. Agency: Yuzhnoye. More at: 8527. Bibliography: 193, 417, 430.
1965 During the Year - . LV Family: R-56. Launch Vehicle: R-56.
Home - Search - Browse - Alphabetic Index: 0- 1- 2- 3- 4- 5- 6- 7- 8- 9 A- B- C- D- E- F- G- H- I- J- K- L- M- N- O- P- Q- R- S- T- U- V- W- X- Y- Z � 1997-2016 Mark Wade - Contact � / Conditions for Use |
